Production Line A diverse range of products to meet most customer requirements from packaging and bookbinding to the construction industry. The following list of products within our 2000 Series gives an idea of our base range, if you require any variation of a product not shown please ask our Sales Department. A range of application equipment and applicator bottles are available upon request.


Water Borne

WOOD GRADES

W2000
High quality wood bonding adhesive is suitable for both hard and soft wood giving high strength on close fitting bonds. It has an open time of 1O to 25 minutes and a high solids content. W2000 is recommended for internal use only

W2001
Wood bonding adhesive offers hot and cold press capabilities with a typical open time of 10 to 18 minutes. W2001 is a filled PVA allowing for internal bonding only.

Product Range
W2005
High performance wood bonding adhesive is suitable for internal and external use. W2005 has excellent water resistance and meets the specification of B1, B2 and B3 under DIN 6B-602. It is suitable for bonding both hard and soft woods and can be hot or cold cured.

Many other wood bonding grades are available such as W2010, a powder form adhesive approved to D3 water resistance specification. W2007 is our high performance wood bonder for exotic woods, giving very high bond strength. Also see our Hot Melt and Solvent Borne Sections for other wood bonding adhesives.

PAPER BONDING GRADES

W2100
is our highly versatile packaging, converting and assembly adhesive. It can be used for carton sealing, board laminating, drum labelling and will also bond most papers, foils and even rigid plastics and phenolic foams. W2100 offers high tack and fast set speed with FDA Approval to 175.105.

W2105
is our high performance, high tack packaging grade suitable for automated or manual use. W2 105 gives a very fast set rate and will bond many difficult surfaces as encountered in the print finishing industry, such as lacquered and varnished boards. It can be heat re-activated after the bond layer has cured.

W2120
Padding adhesive offers flexible bond lines at a fast set speed that can be increased with heat if necessary. W2120 tends not to crack or fracture on joints after curing. Lower and higher viscosity versions are available for difficult papers and even greater flexibility.

W2132
is designed for use in the manufacture of polyester strapping. It also has a multitude of other uses such as trim bonding in the furniture industry. It offers excellent high and low temperature resistance coupled with a degree of water resistance. W2132 meets FDA Approval to 175.105, 176.108, and Section XIV of the BGA.

W2138
high performance emulsion offers high tack levels combined with a fast setting rate. It is suitable for automated systems and will bond many difficult substrates such as varnished and foil laminated boards, rigid and flexible foams. W2138 is approved to FDA 175.105, 176.107, 176.108, and to BGA XIV.

W2167
is a remoistenabie adhesive for use on envelope flaps where resistance to high ambient temperature and humidity is required. It exhibits excellent lay flat and gloss, together with a very fast remoistening speed. W2167 performs well on a wide variety of manila, white and coloured papers, and is suitable for high quality commercial envelopes. W2167 meets FDA Approval under 175.105.

W2168
has been developed as a high tack adhesive for use on medium to high speed window envelope manufacture. It will bond both glassine and synthetic films to a wide variety of papers common in the envelope industry W2168 meets FDA Approval under 175.105.

E.V.A. BASED

Product
W2213
was developed for bonding metallized polyester, paper, polyethylene laminates, PVC and leather cloths to a wide variety of substrates. It is also used for laminating a wide range of substrates to plaster board in the building industry. W2213 offers high tack, good ageing resistance and plasticiser resistance. It is suitable for manual and automatic systems and meets FDA Approval under 175.105.

LATEX BASED

W2314
is our self seal latex adhesive for use in envelope and carton manufacture. The dried film bonds well to itself when slight pressure is applied but will not bond to other surfaces. W2314 can be applied via roller, wheel, stencil and stereo applicators. It also meets FDA Approval under 175.105.

W2323
remoistenable latex adhesive exhibits excellent lay flat properties coupled with an extremely fast remoistening speed. It performs well on a variety of manila, white and coloured papers and is suitable for high quality and commercial stationary. W2323 meets FDA Approval to 175.105.

DEXTRIN BASED

W2416
is a green coloured adhesive suitable for continuous stationary operations. It offers good lay flat and non-wrinkling properties and provides good adhesion to a wide variety of simple paper and board. W2416 is slow setting and will not skin or thicken up during use. It can be applied by wheel, roller, extruder or spray applicator and meets FDA Approval under 21 CFR Section 175.105.

SYNTHETIC BASED

W2505
is a high tack emulsion packaging adhesive for use on automatic equipment. It offers a very fast set rate and bond to a wide range of difficult surfaces such as varnished and foil laminated boards, plastics and rigid foams. W2505 meets FDA Approval to 175.105.

W2525
standard glass labelling adhesive offers good adhesion of labels to glass with FDA Approval to 175.105.

W2580
synthetic emulsion bonds posters to aluminium bill boards. It is easy to apply and offers easy removal. It is suitable for internal and external use.

ACRYLIC BASED

W2610
is a water based acrylic adhesive which remains permanently tacky giving high levels of cohesive strength. It has been developed for bonding synthetic foams and insulation materials to wood and metal facings. W2620 will bond paper, card and some plastics. It has high rates of coverage and a multitude of uses.

CASEIN BASED

W2800
labelling adhesive is used on high speed labelling equipment suitable for labelling beers, wines, spirits and foods. It will bond a wide variety of paper labels and aluminium foils. Due to the high level of initial tack, very low coat weights can be achieved. W2800 meets FDA Approval to 175.105.
adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives adhesives